Kontroler SpeedyBee F405 V3 BLS ESC 4w1 50A 30×30 Stack Tylko dziś

Opis

Kontroler lotu SpeedyBee F7 V3

MCU: STM32F405

Zasilanie: Lipo 3s-6s

Gyro: BMI270

Blackbox: Slot micro SD (4GM Max)

Baro: Tak

BEC 5V/2A 9V/2A

Bluetooth, CameraControl

Waga 10g

Wymiary 42 x 40

Regulator Obrotów 4x50A BLheli_S

Waga 14g

Wymiary 46 x 44

Product NameSpeedyBee F405 V3 30×30 Flight ControllerMCUSTM32F405IMU(Gyro)BMI270USB Port TypeType-CBarometerBuilt-inOSD ChipAT7456E chipBLE BluetoothSupported. Used for Flight Controller configurationDJI Air Unit Connection WayTwo ways supported: 6-pin connector or direct soldering.Blackbox MicroSD Card Slot*Betaflight firmware requires the type of the microSD card to be either Standard (SDSC) or High capacity (SDHC), so extended capacity cards (SDXC) are not supported(Many high-speed U3 cards are SDXC). Also the card MUST be formatted with the FAT16 or FAT32 (recommended) filesystems. So, you could use any SD card less than 32GB, but the Betaflight can only recognize 4GB maximum.BetaFlight Camera Control PadYes(CC pad on the front side)Current Sensor InputSupported. For SpeedyBee BLS 50A ESC, please set scale = 386 and Offset = 0.Power Input3S – 6S Lipo(Through G, BAT pins/pads from the 8-pin connector or 8-pads on the bottom side)5V Output9 groups of 5V output, four +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 4x LED 5V pads. The total current load is 2A.9V Output2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 2A.3.3V OutputSupported. Designed for 3.3V-input receivers. Up to 500mA current load.4.5V OutputSupported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.ESC SignalM1 – M4 on bottom side and M5-M8 on front side.UART5 sets(UART1, UART2, UART3, UART4(For ESC Telemetry), UART6)ESC Telemetry UARTR4(UART4)I2CSupported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc.Traditional Betaflight LED PadSupported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware.BuzzerBZ+ and BZ- pad used for 5V BuzzerBOOT ButtonSupported.
[A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.
[B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware.RSSI InputSupported. Named as RS on the front side.SmartPortUse any TX pad of UART for the SmartPort feature.Supported Flight Controller FirmwareBetaFlight(Default), EMUFlight, INAVFirmware Target NameSPEEDYBEEF405V3Mounting30.5 x 30.5mm( 4mm hole diameter)Dimension41.6(L) x 39.4(W) x 7.8(H)mmWeight9.6g Product NameSpeedyBee BLS 50A 30×30 4-in-1 ESCFirmwareBLHeli_S JH50Wireless ConfigurationFull Configuration Supported in the SpeedyBee appPC Configurator Download Linkhttps://esc-configurator.com/Continuous Current50A * 4Burst Current55A(5S)TVS Protective diodeYesExternal Capacitor1500uF Low ESR Capacitor(In the package)ESC ProtocolDSHOT300/600Power Input3-6S LiPoPower OutputVBATCurrent SensorSupport (Scale=386 Offset=0)Mounting30.5 x 30.5mm( 4mm hole diameter)Dimension45.6(L) * 44(W) * 6.1mm(H)Weight13.8g